System Controller Pro NV series User’s Manual July 2011
4 Function Description (6) LCD Screen To operate the each function in multi-functions menu and view system related information. (7) Multi-functio
5 Function Description (14) IRIS/Focus Button (IRIS) To adjust the IRIS of camera’s lens. (Focus) To adjust the focus of the PTZ camera. (15)
6 Function Description (23) Switch to Emap mode. In Emap mode, user can select different Emap to view(see also Chapter 2.8). (24) Take a quick
7 1.2 Hardware Installation 1.2.1 Connecting with the DVR Server through the USB port The following is an example of System controller installati
8 1.2.2 Connecting with the DVR Server through the RS485 port Through the RS485 port, user can connect multiple DVR servers with the System Controll
9 3. Set the DIP switch of the RS232 to RS485 converter at 4-wire RS485 setting. 4. Using the screwdriver to lose the pin hole of RS485 to RS232
10 5. Connect the RS232 cable to the RS232 port of the RS485 to RS232 converter. 6. Connect another side of RS232 cable to the RS232 port of the
11 1.2.3 Connect a PTZ Camera to System Controller Pro The following is an example of PTZ camera install to System Controller Pro. 1. Connect the
12 Chapter 2 Operating the System Controller Pro 2.1 Using the System Controller for the First Time For the first time using the System Controller,
13 2.1.1 Upgrading the Firmware of the System Controller User can upgrade the newest firmware of the System Controller. For newest fi
COPYRIGHT © 2011 AVer Information Inc. All rights reserved. No part of this document may be reproduced or transmitted in any form, or by any means w
14 2.1.2 Switching to USB DVR Mode When the System Controller is connecting with DVR system through the USB port, the System Control
15 4. Press button to confirm. To cancel the selection, press button. When the “Complete” message appears on the LCD screen, the mode
16 2.1.3 Switching to 485 DVR Mode When the System Controller is connecting with DVR system through the RS-485 port, the System Controller mode sh
17 4. Press button to confirm. To cancel the selection, press button. When the “Complete” message appears on the LCD screen, the mode switch i
18 2.2 Familiarizing with LCD Screen Following will describe the information or icon that display on LCD screen. Main Menu Submenu(Multi-f
19 2.3 Operating the LCD Menu Main Menu On the LCD screen, each function is corresponding to the button on the panel of the System Controller
20 Multi-Function Menu In multi-function menu screen, press the correspond button of the selections to configure/operate. To go back to the main
21 2.4 Select a Camera Select a camera to view, record, or operate. 1. Press button. 2. On the LCD screen will display Camera Select screen.
22 2.5 Locking System Operation Using the lock button ( ) to lock the System Controller for preventing any unexpected situation happen during the
23 2.6 Trigger the Alarm Button The panic button ( ) allows user to trigger the defined alarm button manually. 1. Press button and the Alarm
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION ... 1 1.1 Hardware Introduction ...
24 2.7 To Playback the Recorded File To playback the recorded file on surveillance screen. 1. Press button to switch to playback mode. The LC
25 3. After selected the time and date to playback, the DVR system will start to playback. 4. Using the Jog/Shuttle button to control the playba
26 2.8 To View the Emap User can select the different Emap to view. The Emap ( ) button is same as the Emap ( ) button on the DVR program UI. 1.
27 4. Press TOP MENU button to go back to the main menu screen.
28 2.9 PTZ Operation If the camera has enabled the PTZ function, user can use the System Controller to operate the PTZ camera. i - Please select th
29 Zoom in/out Rotate the joystick to the clockwise side to zoom in and counterclockwise to zoom out. 2.9.2 To Focus the Object Press button to
30 2.9.4 Setup preset position and Use Preset Setup Preset Position 1. Press button and the Camera preset setup screen will appear on LCD screen
31 2.9.5 Enabling the AutoPan Enable/disable the PTZ camera move automatically that is based on the selected camera group preset position number. 1
32 4. To stop auto pan, press selected preset position group number again and press button. When the “Complete” message appears on the LCD screen
33 2.9.6 Using Digital Zoom To zoom in the selected screen area for viewing. 1. In PTZ camera screen, press button. The message “Complete” will
Enable a Camera ... 35 Enable a Camera View ...
34 2.10 Functions in Preview Mode In the following sections will introduce the each function in preview mode. 2.10.1 Select a Monitor Layout In
35 2.10.2 Camera Setup In Camera setup, user can enable/disable the camera, enable/disable camera video to be display on the screen, adjust contras
36 Enable a Camera View 1. First, select the camera to configuration. Please refer to Chapter 2.4. 2. At main menu screen, press the button to e
37 Adjusting the Hue 1. First, select the camera to configuration. Please refer to Chapter 2.4. 2. At main menu screen, press the button to ent
38 Adjusting the Saturation 1. First, select the camera to configuration. Please refer to Chapter 2.4. 2. At main menu screen, press the button
39 Adjusting the Brightness 1. First, select the camera to configuration. Please refer to Chapter 2.4. 2. At main menu screen, press the button
40 Adjusting the Contrast 1. First, select the camera to configuration. Please refer to Chapter 2.4. 2. At main menu screen, press the button to
41 Trigger the Relay of IP Camera 1. First, select the camera to configuration. Please refer to Chapter 2.4. 2. At main menu screen, press the
42 2.10.3 Server Setup In Server setup, user can start recording, stop recording, execute network time synchronization, and call out event log viewe
43 Stop Recording This function is same as press F2 button (see also (9)Custom Button Function in Chapter 1.1.3) 1. At main menu screen, press the
Adjusting the Brightness of LCD Screen ... 66 Adjusting the Contrast of LCD Screen ...
44 Network Time Synchronization To adjust the DVR system time through the network time server that user has configured on DVR server. 1. At main men
45 Open Event Log Viewer To call out the event log viewer window. This function is same as press button on DVR program UI. 1. At main menu screen
46 2.10.4 Sound Setup In Sound setup, user can enable/disable sound and adjust volume output of the System Controller. 1. At main menu screen, pres
47 2.10.5 Controller Setup In Controller setup, user can configure the parameters of the System Controller Pro. Set a Password for System Controll
48 4. Press button to enable password function. 5. The password enter screen will appear. Using numeric key pad to enter the password (6 numbers
49 Change the Password of the System Controller i The password function will be enabling after password changed. 1. At main menu screen, press the
50 6. After entered the current password, the new password screen will appear. 7. Using numeric key pad to enter the new password (6 numbers) and
51 Set the Timer Set a System Controller idle time period to switch to rest status. 1. At main menu screen, press the button to enter Controller
52 Adjusting the Brightness of LCD Screen To adjust the back light brightness of the LCD screen. 1. At main menu screen, press the button to enter
53 Adjusting the Contrast of LCD Screen 1. At main menu screen, press the button to enter Controller setup screen. 2. Press button to enter L
54 Enable/disable Code Number Display 1. At main menu screen, press the button to enter Controller setup screen. 2. Press button to enter LCD
55 Enable/disable Button Confirmation User can enable/disable to display a confirmation screen when press custom function buttons (F1~F8) and Alarm
56 Viewing System Version Information 1. At main menu screen, press the button to enter Controller setup screen. 2. Press button to enter Syst
57 2.11 Functions in Playback Mode In the following sections will introduce the each function in playback mode. 2.11.1 Select a Monitor Layout In
58 2.11.2 Camera Setup In Camera setup, user can enable/disable de-interlace function. i Camera Enable ( ), Display ( ), Attribute ( ), and IP-CAM
59 2.11.3 Server Setup In Server setup, user can call out event log viewer windows. Open Event Log Viewer To call out the event log viewer window.
60 2.11.4 Sound Setup In Sound setup, user can enable/disable sound and adjust volume output of the System Controller. 1. At main menu screen, pres
61 2.11.5 Controller Setup In Controller setup, user can configure the parameters of the System Controller Pro. i The Button Confirmation ( ) and
62 3. Press button to enter the Password setup screen. 4. Press button to enable password function. 5. The password enter screen will a
63 Change the Password of the System Controller i The password function will be enabling after password changed. 1. At main menu screen, press the
1 Chapter 1 Introduction The AVerTM System Controller Pro provides user an easy way to operate DVR server . 1.1 Hardware Introduction 1.1.1 Left
64 6. After entered the current password, the new password screen will appear. 7. Using numeric key pad to enter the new password (6 numbers) and
65 Set the Timer Set a period time for System Controller idling over the setup time to switch to rest status. 1. At main menu screen, press the b
66 Adjusting the Brightness of LCD Screen To adjust the back light brightness of the LCD screen. 1. At main menu screen, press the button to enter
67 Adjusting the Contrast of LCD Screen 1. At main menu screen, press the button to enter Controller setup screen. 2. Press button to enter L
68 Enable/disable Code Number Display 1. At main menu screen, press the button to enter Controller setup screen. 2. Press button to enter LCD
69 Viewing System Version Information 1. At main menu screen, press the button to enter Controller setup screen. 2. Press button to enter Sys
70 Chapter 3 Operating in PTZ 485 Mode The PTZ 485 mode is to control the PTZ camera that is directly connected with System Controller through the R
71 4. Press button to confirm. To cancel the selection, press button. When the “Complete” message appears on the LCD screen, the mode switch i
72 3.2 Select the Protocol of the PTZ Camera Selecting the PTZ camera – Pelco-P or Pelco-D. 1. In 485 PTZ mode menu screen, press button to en
73 3.3 Setup the Baud Rate of the PTZ Camera Selecting the baud rate of the PTZ camera. 1. In 485 PTZ mode menu screen, press button to enter
2 1.1.2 Rear Side Function Description (1) RS485 Port For connection of Pelco-D/P PTZ camera and using RS485 to RS232 converter to connec
74 3.4 Controller Setup In Controller setup, user can configure the password, timer, brightness and contrast of the LCD screen, switch mode, and
75 3. Press button to enter the Password setup screen. 4. Press button to enable password function. 5. The password enter screen will ap
76 3.4.2 Change the Password of the System Controller i The password function will be enabling after password changed. 1. At main menu screen, pre
77 6. After entered the current password, the new password screen will appear. 7. Using numeric key pad to enter the new password (6 numbers) an
78 3.4.3 Set the Timer Set a period time for System Controller idling over the setup time to switch to rest status. 1. At main menu screen, press t
79 3.4.4 Adjusting the Brightness of LCD Screen To adjust the back light brightness of the LCD screen. 5. At main menu screen, press the button
80 3.4.5 Adjusting the Contrast of LCD Screen 6. At main menu screen, press the button to enter Controller setup screen. 7. Press button to e
81 3.4.6 Viewing System Version Information 1. At main menu screen, press the button to enter Controller setup screen. 2. Press button to en
AVer Information Inc. Taiwan & International 5F., No.135, Jian 1st Rd., Zhonghe Dist., New Taipei City, Taiwan TEL: 886-2-2226-3630 FAX: 886-2-
3 1.1.3 Familiarizing with System Controller Panel Buttons System Controller Panel figure Function Description (1) (Lock) To lock panel butto
Comentarios a estos manuales